Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Inspection for Stockton Homeowners
Stockton’s burning season is short and the valley air sits heavy, so a chimney that drafts poorly or smells smoky in the off months is telling you something worth hearing. We’re chimney-only specialists. Our technicians have up to 13 years of experience, and every recommendation starts with a proper inspection, not a sales pitch. We see the same patterns across Stockton homes: older masonry flues with cracked mortar joints, factory-built fireplaces from the 1980s and 90s with tired liners, and caps that have gone missing or rusted loose under years of valley heat and rain. A thorough inspection catches those problems while they’re still small. Nothing gets recommended without camera evidence you can look at yourself, and we’ll tell you plainly when work can safely wait. Same-day visits are usually possible when you call early. Reach us at (877) 516-9568.
Fireplace Inspection
Fireplace Inspection looks at the firebox, damper, smoke chamber, hearth, and the immediate flue above it as one connected system rather than a single part. You need one when you’re buying a home with a fireplace, after a long gap between fires, when smoke spills into the room instead of drafting up, or when you’ve never had the unit looked at. We work Stockton homes with both wood-burning masonry fireplaces and factory-built units, and the two need different checks. Our technicians photograph what they find and show you the images before anything is discussed. A fireplace inspection in Stockton typically runs $125 to $250 depending on the type of unit and how much access the firebox allows. When a problem shows up, we handle the repair ourselves rather than handing you to someone else.
Firebox and Damper Checks
We check firebox brick and mortar for spalling, gaps, and heat damage, and test the damper for smooth operation, a tight seal, and correct linkage. These are small failures that quietly let heat and smoke past where they shouldn’t go.
Factory-Built Unit Verification
Factory-built fireplaces have manufacturer clearances and liner ratings that masonry units don’t, and those specs govern what’s safe. We verify the unit is being used within those limits and flag any modification that changed them.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Chimney Inspection Services
Chimney Inspection Services cover the whole exterior and interior structure: crown, cap, flashing, masonry, flue, and all visible connections. You’ll want a full inspection annually if you burn regularly, before your first fire of the season, after a chimney fire or seismic event, and before selling or buying a home in Stockton. We inspect with a flashlight, a camera, and a level of patience most generalists don’t bring, because chimney work is the only trade we practice. The report is written in plain language with photos attached, not a checklist full of jargon. Full chimney inspection services in Stockton generally fall in the $150 to $350 range, with camera work and length of the flue affecting where you land. If a repair is needed, we quote it in writing before any work begins.
Exterior Structure Assessment
Crown cracks, washed-out mortar joints, and loose flashing are the first places valley weather shows up. We document each one with photos and rate how urgent it actually is.

Written Findings Report
You get a clear written summary of what’s sound, what needs watching, and what needs work, with photos of each. It’s yours to keep, and we’re happy to walk through it with you.

Chimney Flue Inspection
Chimney Flue Inspection focuses narrowly on the inside of the flue itself: its size, its liner condition, and whether the liner is continuous and correctly sized for the appliance attached to it. It’s the check that matters most for creosote glaze, cracked clay tiles, liner gaps, and the kind of hidden damage that never shows on the outside of the house. We run it whenever a fireplace has gone unused for years, when you’ve had a fire you’re unsure about, and whenever draft problems suggest the flue isn’t doing its job. Our technicians use a camera to reach bends and offsets that a flashlight can’t. A chimney flue inspection in Stockton typically costs $175 to $300, and it’s usually bundled with a sweep so you’re not paying twice for setup. We install DuraFlex flexible liners and use HeatShield ceramic restoration where the existing flue can be saved, so we can offer you both routes honestly.
Liner Condition Mapping
We review the full length of the liner, note cracks, gaps, and missing mortar, and mark each weak spot on a flue diagram you keep. That makes the repair conversation concrete instead of abstract.
Sizing and Draft Evaluation
An oversized flue cools smoke before it clears the top, and an undersized one chokes the fire. We measure and match the flue to the appliance, which often explains draft complaints that look like something else.
Chimney Fire
Chimney Fire leaves damage that isn’t always visible from the hearth, which is why we recommend an inspection after any fire you suspect went into the flue. The warning signs are a roar like a freight train, popping sounds, flames or dense smoke at the top of the chimney, and a strong burning smell that lingers afterward. Creosote buildup is the common fuel, and it accumulates quietly with every fire, especially in wood that hasn’t been well seasoned. Even a small flue fire can crack clay tiles, warp a metal liner, or open joints that let heat reach framing. We inspect and diagnose the damage, then repair the liner with DuraFlex or restore it with HeatShield where the flue can be saved. Post-fire inspection and repair estimates usually start around $250 and climb with the scope. Call (877) 516-9568. We answer 24/7.
Post-Fire Damage Assessment
We look for tile cracks, warped or buckled metal liner sections, and heat damage to the smoke chamber and crown. The camera shows what a flashlight misses, especially at flue offsets.
Repair or Reline Options
Where the flue is intact enough, HeatShield ceramic resurfacing restores it without masonry demolition. Badly damaged flues usually need a DuraFlex liner, and we quote both so you can compare.
Level 2 Chimney Inspection
Level 2 Chimney Inspection is the fuller inspection that goes beyond what’s visible from the hearth: the accessible portions of the attic, crawlspace, and roofline are checked along with the flue and all its connections. You need one when you’re buying or selling a home, after a chimney fire, after an earthquake or a major storm, when you’ve changed appliance type, or when a Level 1 has turned up something worth investigating further. We work through the whole assembly methodically and photograph every notable finding, including clearances to combustibles that only show up in an attic. A Level 2 inspection in Stockton typically runs $250 to $450 depending on roof access, number of flues, and how much of the attic is reachable. If we recommend a repair, the report shows you exactly why, and we’ll tell you if it can safely wait a season.
Attic and Crawlspace Access
Clearances to framing, hidden flashing leaks, and abandoned flues all show up here and nowhere else. We check what’s accessible without disturbing insulation or finishes.
Real Estate Transaction Reports
Buyers and sellers both benefit from a report that documents the chimney’s actual condition rather than a verbal summary. You get photos and written findings, ready to share with your agent.
Chimney Leak
Chimney Leak symptoms usually show up on the ceiling or the face of the chimney rather than at the top, so the source takes some tracking down. The common culprits are a cracked crown, failed flashing where the roof meets the chimney, missing or undersized caps, and masonry that has absorbed water and needs sealing. Stockton’s dry summers followed by winter rain make those cracks open up and then fill, which is when staining and damp patches appear inside the house. We trace the water path before recommending anything, because the fix for a flashing leak is not the fix for a crown leak. Gelco caps, correctly sized and sealed, close off one of the most common entry points for both water and animals. Chimney leak diagnosis and repair in Stockton typically runs $200 to $600 depending on the source and extent. Call (877) 516-9568. We answer 24/7.
Water Path Tracing
We check the crown, flashing, cap, and masonry in sequence and use water testing where the source isn’t obvious. Guessing at a leak wastes your money and lets the real problem keep working.
Crown and Cap Sealing
A sound crown sheds water away from the flue, and a correctly fitted cap keeps rain and animals out. We repair crowns and install Gelco caps sized to the actual flue opening.
Chimney Camera Inspection
Chimney Camera Inspection sends a video camera down the flue so the entire interior can be seen on screen, including offsets, bends, and the smoke chamber that a flashlight can’t reach. It’s the right call whenever damage is suspected but not confirmed, when a home has changed hands and the flue history is unknown, and when you’ve been told you need a liner and want to see the evidence before deciding. We record the run and review it with you, so the recommendation is grounded in something visible rather than a verbal claim. Materials in our lineup, including Olympia Chimney and Famco venting components, are specified only when the camera actually shows a need for them. A chimney camera inspection in Stockton typically costs $150 to $275 on its own and less when bundled with a sweep. It’s the single best defense against unnecessary repair work.
Video Footage Review
We pause the footage at every notable point and explain what you’re seeing in plain terms. You walk away knowing the condition of your flue, not just what someone told you.
When the Camera Changes the Plan
Sometimes the footage shows a flue that’s sounder than expected and the repair can wait. Sometimes it reveals a gap no external check would have caught. Either way, the plan follows the evidence.
Brands We Service
We work with HeatShield ceramic restoration for flues that are sound enough to be resurfaced rather than replaced, and we’ve seen how well it holds up when the prep work is done right. HeatShield is our preferred route when it saves a homeowner the cost and disruption of a full reline, and we bring the same care to applying it that a full liner job gets. Gelco caps are part of the same lineup: sizing, sealing, and fitting matter as much as the cap itself, and a poorly fitted cap causes more problems than it solves.
Olympia Chimney and Famco venting components round out the professional-grade materials we install. We specify these because they’re the same products certified chimney specialists across the country rely on, not off-brand substitutes that might save a dollar and fail in three years. We’re not a dealer, but we know how these components wear and where they fail, and that knowledge shows up in how we specify a repair. Whether you have HeatShield, Gelco, Olympia Chimney, Famco, or any other make, we can help.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- A strong smoky smell in warm weather. That odor means creosote in the flue is reacting to heat and humidity, and it’s the same deposit that fuels a chimney fire. It won’t clear on its own and usually signals buildup worth inspecting.
- Smoke spilling into the room. A fireplace that backdrafts is usually fighting a blocked flue, an undersized one, or a pressure problem the house is creating. Spilling smoke is your cue to stop burning and get it checked.
- Water stains on the ceiling or chimney face. Damp patches point to a leak at the crown, flashing, or cap, and the longer it runs the more masonry it takes with it. Water damage compounds fast once it gets into the structure.
- Visible cracks or crumbling mortar. Cracks in the flue tiles or joints in the brickwork let heat and gases move where they shouldn’t. This is the kind of damage a camera inspection settles quickly.
- A fire you suspect went into the flue. Loud roaring, popping, or flames at the top of the chimney mean heat reached the liner. Even if nothing looks wrong afterward, the flue needs a proper post-fire inspection.
Our Process, Step by Step
- 1
Talk through what you’ve noticed. We ask about draft, odor, staining, and how often you burn so the inspection targets what actually concerns you. That conversation shapes where we look hardest.
- 2
Inspect from the hearth and the roof. We check the firebox, damper, smoke chamber, and flue, then move to the crown, cap, and flashing on the roof. A level is used where clearances or drainage slope need confirmation.
- 3
Run the camera. The flue gets a full video run so every offset and liner joint is visible on screen. We pause at each finding and show you what we’re seeing.
- 4
Review the findings together. We walk through the photos and footage, explain what’s urgent, what needs watching, and what can wait. You get a written report with the images attached.
- 5
Quote any repair in writing. If work is needed, you get a clear scope and price before anything starts. We do the repair in-house rather than handing you to another contractor, so accountability stays with one team.
How Much Does Chimney Inspection Cost in Stockton?
Chimney inspection in Stockton typically costs between $125 and $450, and the level of inspection determines where you land within that range. A basic fireplace inspection usually runs $125 to $250 depending on the appliance type and access. A full chimney inspection services visit with camera work typically lands between $150 and $350. A Level 2 inspection, which adds attic, crawlspace, and roofline access, generally runs $250 to $450. Camera-only inspections sit at the lower end at $150 to $275, and bundling them with a sweep brings the combined cost down compared to booking each separately.
What affects the price most: the number of flues in the house, roof pitch and ease of access, whether the attic is reachable, and how much camera footage the flue requires. A tall chimney with multiple flues takes longer than a single straight run. Old fireplace inserts and unfamiliar factory-built units can add time because clearances need verifying. The best way to avoid overpaying is to understand what’s included before you book. A written report with photos and video should be standard, not an upsell. If a contractor recommends liner replacement without showing you the footage, ask to see it. We won’t recommend work without camera evidence you can inspect yourself, and the estimate itself is free.
Our Service Area Near Stockton
We inspect chimneys throughout the Stockton area, including Country Club, August, Garden Acres, Kennedy, Morada, French Camp, and Woodbridge, along with Lodi, Lathrop, Manteca, and Lockeford. Response times vary by neighborhood and how early in the day you call. Most appointments in the core Stockton area are scheduled within a day or two when the calendar allows, and outlying towns usually take a little longer. Call and we’ll give you a realistic window for your address.
Serving Stockton, CA – Our Local Coverage Area
We serve Stockton and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Chimney Inspection in Stockton
A chimney inspection is a professional assessment of the fireplace, flue, and chimney structure to check for damage, buildup, and safety issues before they become costly repairs. It covers the firebox, damper, smoke chamber, flue liner, crown, cap, and flashing, with a camera added where the flue needs closer review. You get a written report with photos showing what was found. Call (877) 516-9568 for an exact quote on your inspection.
A standard inspection usually takes 45 minutes to an hour and a half, depending on how many flues the home has and how easy roof and attic access turn out to be. Level 2 inspections take longer because the attic and roofline are part of the visit. Bundle it with a sweep and the appointment runs longer still, but you save a separate trip. Call (877) 516-9568 to schedule a window that fits your day.
A chimney inspection in Stockton typically costs between $125 and $450, with the level of inspection determining the price. Fireplace inspections usually run $125 to $250, full inspections with camera work $150 to $350, and Level 2 inspections $250 to $450. Bundling the inspection with a sweep usually brings the combined cost down. Call (877) 516-9568 for an exact quote. Estimates are free.
Yes, we work with Olympia Chimney and Famco venting components as part of our professional-grade materials lineup, along with DuraFlex, HeatShield, and Gelco. We’re not a dealer, but we know how these products wear and where they tend to fail so the right repair gets specified the first time. Our technicians have up to 13 years of experience across all the core chimney brands. Call (877) 516-9568 to ask about your specific setup.
Same-day inspections are often possible when you call early in the day, depending on the schedule and your location in or around Stockton. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday. We’re closed on Saturday, so a call outside dispatch hours is booked into the next opening. Call (877) 516-9568 and we’ll give you a realistic window for your address.
We stand behind our inspection findings and the repairs we complete, and the working terms are spelled out in the written estimate before any work starts. If something we installed or repaired isn’t performing as it should, we return to look at it. The inspection report and its photos are yours to keep. Call (877) 516-9568 with any questions about the terms on your job.
Clear the hearth and a few feet in front of the fireplace, and make sure we can reach the roof access and attic hatch without moving furniture. Stop burning for at least 24 hours before the appointment so the flue has cooled. If you have records of past chimney work, have them handy; they help us understand what’s been done before. Call (877) 516-9568 if you have questions about access.
Schedule Your Chimney Inspection Service in Stockton Today
Whether you’re due for an annual inspection, you’ve noticed smoke, odor, or staining, or you’re buying a home in Stockton, we’re ready to take a proper look. Our estimates are free, the written report is yours to keep, and nothing gets recommended without camera evidence you can see for yourself. Call (877) 516-9568. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Reach out to Stockton Chimney Sweep and get your inspection scheduled.
Written by the team at Stockton Chimney Sweep.